While it’s taken a lot of words to describe the process, it’s quick, easy and foolproof. Using Futures you unscrew the front of the fin, slide Finsout over the front of the fin and leverage up. With FCS II you approach the fin from the rear and first leverage up the rear of the fin out of the box then the front of the fin. The patent-pending design, enables you to change your FCS II fins with a simple flick of the wrist. FEATURES Overview Fin removal tool compatible with the FCS II fin system. With FCS II, if you don’t approach the fin release just right you can damage your board, even popping out the entire fin box. Swapping the fins out of your surfboard just got a whole lot easier. Removing the fins is where Finsout is most valuable. Benefit: Easily Insert Or Remove Your Fin In Seconds. Then use Finsout to leverage down the rear of the fin into the box. The FCS II Tool-less Touring Fin 9 from Boardworks provide larger surface area Than Dolphin Fins. With FCS II you place the front of the fin in the box. Then use Finsout to leverage down the front of the fin into the box.
The patent-pending fin friendly design, which enables you to change your FCS II. With Futures this means inserting the fin into the rear of the box. The Finsout tool is a device to help you remove your FCS II fins from your board without them flying off into the air. Finsout is a handy tool compatible with the revolutionary FCS II fin system. Then exert pressure on the part of the fin that is not in your box. With the FCS II system, the need for any screws or tool to secure the fins has been.
Fcs 2 fin removal tool how to#
You then slide the Finsout Removal Tool over the fin. This video demonstrates how to insert & remove your FCS II fins. To insert a fin you place your fin partway in the fin box. These two side pieces are connected to a solid handle at the back to safely and easily leverage out your fins. There’s two side pieces with a padded space in the middle. It’s shaped and works in a similar way to a pair of tongs. The Finsout is a simple yet sophisticated device that helps you insert and remove your fins. Or you can push the back of your fin into your board causing a ding. Not only can these fins be hard to move, if you apply too much of the wrong force you can wreck your fin box, popping it out. Finsout Fin Removal Tool £15.95 Unfortunately, this product is currently out of stock. The reason you need this is that fins can get stuck, from sand and salt build up, or from an odd bump. The Finsout Removal Tool for FCS II & Future Fins gives you safety and easy removal of your surfboard fins. The fin should release from the plug, and roll out easily.Description Finsout Removal Tool for FCS II & Future Fins Using both hands to encourage the motion, lift and roll the fin up and forward towards the nose. Finsout Fin Removal Tool - Fin removal tool compatible with the FCS II fin system.enables you to change your FCS II fins with a simple flick of the wrist. To remove the fins, firmly hold the top of the fin with one hand, and with the other hand brace the fin between your thumb and pointer finger, while keeping the back of that hand on the board for support. Choose between three fins for a thruster, and 4 fins for a quad. Once engaged, simply apply downward pressure until the fin clicks into place.Īt this point the fin should be sitting flat with the bottom on the board. To insert the fin push the front of the fin into the plug first so the ridge inside the plug engages with the recess in the forward tab.
Fcs 2 fin removal tool install#
Centre fins have a symmetric 50/50 foil and are used in the rear plug.īefore you install your fins you should ensure you board is on a stable surface to avoid damage, and it’s also a good idea to have one hand under the rail for support. The convex or curved side of the fin always faces out, and should be positioned in the front plugs. Side fins have a flat surface on the inside face, and a convex foil on the outside face.
Firstly identify the centre and side fins.
0 kommentar(er)
